To replace my tripod head that was starting to not hold the weight of my kodak anymore she is really tough!!!
The plate is compatible with my old quick release fak it's perfect!
I advise to check the tightening of the plate on the ball joint because I had to put a tork to stabilize it (the Allen key is provided!)

I'm a tripod guy - I have at least a dozen. I have compact models for travel, large rugged models when I need a rugged model, carbon fiber, aluminum and a combination. After using this tripod a few times, you'll find that whoever designed it took the best qualities of several tripods and combined them here - although some have escaped them.

All dials and buttons are aluminum, not plastic. This is really nice and adds years to the life of the tripod. Plastic buttons eventually break. They break if bumped too hard. Aluminum has dents or scratches, but it doesn't shatter like plastic.

All hardware (connecting screws, nuts, bolts) is rust-free.

The included ball head is pretty damn nice too. It has the thicker 3/8-24 thread typical of a tripod head. The plate is an Arca-Swiss style sliding plate and the camera screw has a built in thumb lock for hand tightening. No tools (or coins) are required. The plate can be detached and slid back and forth, but will not slip off the head. It takes almost two full turns of the locking knob to fully disengage the panel. Kind. There is also a built-in soap scale. The ball mechanism is in a Teflon pocket and is therefore smooth-running.

At the top of the tripod (where the head attaches) is a reversible screw - 1/4-20 for cameras or 3/8-24 for tripod heads. The top orange collar ensures it stays in place. It's all hand tightened, so it's possible to twist the ball head off without realizing it. There are no locking screws to fix the tripod head. The best way to attach the head is to remove the double ended screw and collar. On the tripod head, loosen the large locking wheel and move the plate to the 45-degree position (so it sticks in the notch.) Turn the tripod mounting screw until it stops — it's actually pushing against the ball at this point. Now turn up the orange collar. Loosen the screw half a turn. Tighten the collar as tight as possible (no tools!) Now twist and tighten on your head. You'll find that it's a lot harder to accidentally spin off.

Anyway, a great tripod, a little heavier compared to compact or carbon fiber models, but a good choice for all-round use. Also, it is very convenient to switch to a monopod in less than a minute.

Great in general - However the head bolt is stuck in to the head and not the tripod so mounting another head is out of the question without obtaining a secondary bolt.

I bought the carbon tripod because I finally wanted a ball head :-). The tripod is incredibly light and remains very stable. The screw caps can be easily opened and then securely fastened again. The camera sits perfectly on the ball joint and is then super adjustable. The fixing screws are easy to move and yet very easy to fix.

When the camera is attached to the ball head mount with the plate, the spirit level is on the side of the screen, where it suits me. BUT the wheel to fix the plate is then on the side of the lens. With my Sigma, however, the rotary knob is almost on the lens. There are only tenths to hundredths between the rotary knob and the lens.

Otherwise the tripod is a recommendation:

- Weight
- stability
- size
- flexibility
- rapid deployment

Looking for a light and compact tripod for organizing a trip, I came across this one, barely 1kg300 for 38cm folded. It also carries the possibility of making a monopod very quickly, which will be interesting to capture an image in a place where the tripod would not have been possible.

For this small build, the tripod is very solid, since it easily supports the weight of my 6d mark ii with its grip and its two batteries + a sigma 70-200. (even with the articulated arm deployed).

The legs of the tripod have 5 sections, which allows it to go from around 35cm to 155cm and the central column can be reversed to allow the device to be placed at ground level!

It comes with a carrying bag, an extension for the monoball monopod, a ball head with an "arca swiss" type quick plate which allows the lens to be attached directly to the ball head without using the quick plate (see photo 4).

In conclusion, a purchase that I do not regret and which for its price is more than qualitative.

Very functional, lightweight and compact tripod. Only the rubber ring on the mounting plate of the camera body could be more anti-slip

do a lot of landscape photography, and while shutter speeds often allow hand-holding, there's a distinct, visible advantage to tripod-mounting your camera. Not only does it reduce vibration, it also allows different shutter speeds to be used without risk of camera shake for flowing water, for example. I have several tripods, some sturdier (and hence heavier) than others, and usually have a mid-weight tripod in my car. This K&F Concept tripod is what I would consider mid-weight, at 1.8kg, yet it is sturdier than I expected for that weight.The tripod is made of carbon fibre, which gives it strength without too much weight, and it looks good! The tripod comes with a metal ball mounting head that will support cameras up to 16kg. At first, I thought the tripod would be more suited to videography, but using it for photography with my Nikon Z-series and a big telephoto lens, I think it works for both quite well. It extends out to 68 inches height, and can work as both a tripod and a monopod. Not all photographers like ball heads (they have their advantages and disadvantages) and I did replace the ball head with a three-axis head for a while, but I kinda like the ball head on this tripod.I've been using the tripod for a couple of weeks so far, and I like it. It doesn't weigh much, so is easy to move with me in a shoulder bag, and it has proven to be a solid mount so far. I like the look of the tripod, too. It is not a cheap tripod, and there are competing models on the market, but the combination of carbon fibre and easy of portability makes this a tripod to use every day.

I bought the carbon tripod because I finally wanted a ball head :-). The tripod is incredibly light and yet very stable. The screw caps are easy to open and then tighten again. The camera sits great on the ball head and is then super adjustable. The fixing screws are smooth-running and yet very easy to fix. 1.: Unfortunately for me there are 2 small weaknesses in the product: The clamps for adjusting the tripod feet rattle incredibly. I always have to worry that the clamps will fall off. 2.: When the camera is attached to the plate on the ball head mount, the spirit level is on the side of the display, which I think is ok. BUT the knob for attaching the plate is then on the side of the lens. With my Sigma, however, the rotary knob is almost on the lens. There are only 10ths to 100ths between the rotary knob and the lens. I find this ugly.Otherwise, the tripod is a recommendation.Positive:-Weight-Stability-Size-Flexibility-faster useNegative:-Clamp to adjust the tripod legs rattle-Setting screw for attaching the mounting plate camera/ball head very, very, very tight to the Tripods from SigmaNevertheless a clear recommendation on my part.