The adapter fits smoothly into the EOS bayonet without wobbling (in my case: 6D and Film-EOS 33v). The F bayonet on the lens side is also very nicely made - with many similarly inexpensive adapters, the retaining aluminum lamellae of the F bayonet are only used a slit is cut and then the slats are slightly bent up. The more stable and also more precise solution are of course 3 small leaf springs that press the lens evenly against the bearing surface of the bayonet - as is the case with this adapter.

Yes... it works perfectly with Canon EOS M cameras. I own Canon EOS M10 and use this adapter most of the time with Canon 50mm 1.8 lens. It is amazing. The autofocus is accurate and fast enough. If you own a Canon EOS M camera, I recommend you this adapter because it is much cheaper than Canon original and there is actually no difference between them. Everything works as it should. I love this adaptor. The best purchase I've made for my camera.

With this adapter I can use my old MINOLTA lenses on the Canon EOS R. Works well. The connections run smoothly and the lenses are tight. But you have to be aware that the aperture and distance on the lens have to be set manually. "Release without lens" must be activated on the EOS R (menu 5/5). Otherwise the camera will not trigger. Set to Av aperture priority.

The lens adapter is used by me to use high quality Nikon lenses on a Canon EOS M camera. The adapter is of high quality, the handy metal ring allows manual adjustment of the aperture. Note: electronic transmission of the lens data or the autofocus is not possible with this adapter!

have an EOS 350D available on which I want to test the use of my Nikkor AI lenses. I received the adapter ring today and tried it out right away. The processing of the adapter ring is very good, the connection to the camera works perfectly. Since there is no description, you first have to think about the correct attachment to the lens (description below). When this is done, the ring can be put on and fastened (relatively stiff). Detaching the ring from the lens is also relatively difficult, not at all for me at first until I found the right procedure and "practiced". A point is deducted for the missing description. All in all, a recommendable adapter. It remains to be seen whether the problems identified so far with the EOS can be solved with connected AI lenses. Description of connection/dismantling of the adapter lens: Set the maximum f-number on the lens. Position the adapter with its red dot opposite the black dot on the lens. Fasten anti-clockwise (movable pin of the adapter goes into the U-groove of the bayonet ring). This also ensures that the lens is correctly aligned when the adapter is connected to the camera (aperture and distance settings visible from above). To disassemble the adapter, hold the aperture ring with one hand and use the index finger of the other hand to press down on the small release lever while turning the other fingers clockwise to release the adapter from the lens.

Since I recently inherited a Nikon FG-20 as well as a Nikon Micro-Nikkor 55mm f/2.8 and a Nikon Series E manual focus zoom 70-210mmf/4.0s, I naturally wanted to use the old lenses on my Canon EOS 600D or EOS 600D Review Canon EOS 760D. But: Nikon on Canon? It is well known that this is not possible without an adapter ring. Novoflex adapters were out of the question for me, because as a hobby photographer and occasional "analogue photographer", I didn't want to spend €100 on such a ring. Nevertheless, I wanted to break THE primal law of photography and combine Nikon and Canon. K&F Concept offered a cheap alternative for just under €20. The adapter ring is surprisingly high-quality and made of metal, and it can also be quickly mounted on the lens and DSLR. I was surprised by the results (see photos) and would not have thought that the two 30-year-olds "harmonize" so wonderfully with my EOS, to put it bluntly. It's a bit "hooky" to detach the adapter ring from the lens again using a tiny little "hook" (if you can call it that...), so the ring gets a star deduction, because it gave me a bit of a panic at first and I'm not sure how long this "hook" will go along with the whole procedure. ! A NOTICE ! You should really inform yourself in detail about the bayonet (connection of the lens) beforehand. Since the two Nikon lenses are both a bit older and were built in a time when people would have laughed about something like the internet in this country, it was a bit difficult to find out exactly (especially as a layman or newcomer to Nikon and analogue photography) whether they both have the same connection and whether I might even have to buy two different rings.

I can only recommend the adapter. I ordered the adapter to be able to use the lenses of my Canon A1 on my Canon EOS 400 D as well. Everything fits without any problems, nothing wobbles or jams, even though the lenses on my A1 are from different manufacturers

Processing is good and the picture quality is good.
Inexpensive adapter (with lens) that also works.
Tested on EOS 450 and 80D