Best for the price.
I would buy it again right away.
When I think about what my Manfrotto with ball head cost me before!

K& F concept aluminium tripod with 180 degree tiltover camera head

Summery: Lightweight, sturdy, the tiltover head gives a special feature I wanted.

I own quite a few tripods and camera mounts because I have so many cameras so this one joins my collection for a special reason which I will explain in a short while.

The model is KF-TM2515T

It has 4 part telescopic legs that extend to a give a maximum tripod height of 6o inches, the legs can be used in 3 different angle positions which is adjusted using the red button at the top of each leg, there is no central connector so each leg angle can be set individually.

The centre column is in 2 parts, the outer part can be height adjusted while the second section can not only be extended vertically but it can also be tilted over 180 degrees, it was this feature that made me decide to add this to my collection, more on that in a while.
As with a lot of tripods you can invert the centre column to allow low level and macro shooting, but the tillable section adds a little extension to give a different view than one bound to the centre, you can even make an ad-hoc slider shot by slowly moving the bar along the centre column.

The tripod head is a standard 3/8 thread panning ball-head type that are found on many of my tripods, I like ball-heads for my smaller cameras. It has an Arca-Swiss type quick release clamp with a bubble for camera levelling.

The tripod is lightweight, strong, it folds down pretty small and comes with a strong looking zipped case with straps so for general purpose use it is great, with the added tilt feature to give some extra creative assistance.

Now the reason I bought this particular tripod…..I need to be able to mount 2 cameras on one tripod properly, and this tripod helps me do just that with a little bit of extra kit.
The end of the centre bar has a small plastic cap screwed into it, when taken away a 3/8 thread is revealed, most of my tripod centre column have this, it is usually there to hold the sandbag hook screw. So by using a short 3/8 inch threaded bar and an extra ball-head I can make a double tripod. Fantastic and very useful to save space when shooting.

One leg can also be removed and used with the centre column as a monopod but I already have monopods so I will not be using that feature with this tripod.

Amazing Tripod, replaced this from a 30 dollar tripod that I got from Best Buy. Most definitely recommend this.

I attach cameras to the bracket.I found out my two cameras CANNOT be tighten to the adapter.As if the screw is too long.What gives?Are all tripods like that ?Or defect? Other then that nice tripod.

ABSOLUTE BUY RECOMMENDATION!!!!!

I have 2 cameras and several lenses, power supplies and 2 tripods, I also have a computerised mount for astrophotography. It All fit! As we know it is the horizon that can make or break a "star show" this will allow me to travel off the beaten trail for those "places" of wonder.As far as cons... well if you need speed to get your camera out the front pack can accommodate this. it is a bit bulky for action shots however if you landscape its good for one of the smaller wide angle lenses, diameter is limiting however, and fits my Nikon with a mounted lens quite nicely.

My camera would feel left out if I didn't have these filters.

Buy several of K&F's filters, and while the brand disappoints when it comes to tripods, it more than makes up for it when it comes to filters. This kit is excellent, at the level of optical quality, and materials.
They have almost no color cast or chromatic aberrations, as well as no loss of image sharpness.
Highly recommended, especially since the ND1000 can go head to head with a Lee Big Stoper, and deliver better results for a fraction of the price.

The only drawback that it has, like all KITs, is that it does not come with a case to store everything (the K&F case is sold separately and is quite small for my needs).